YOSHIMURA F1 1988-'92
Back in 91′ Airtech was instrumental in getting the AMA to allow different styled bodywork to be used in the Superbike classes. Due in part to our petitions to the AMA Airtech was able to design new bodywork for several different factory teams.
The whole assembly was used by Yoshimura at the end of the 91′ season and on some of their Formula 1 bikes.
In the old catalogue pictures with the girls, there’s a ’91 fairing on the left and a ’92 version is shown on the right.
This stuff is perfect if you are restoring a Yoshimura F1 or building your own GSXR replica version. We campaigned for this bodywork. It worked, and it will look gorgeous on your GSXR!
Will fit the following models:
GSXR750 1988-’92
GSXR1100 1989-’93
Takes a special windscreen and custom bracket
Ever heard of UFO? The “Unlimited Flying Object” was a popular series of articles in the then new Sportbike Rider magazine. We’re talking ’92 or so. Each issue, they would pit several street bikes against each other in three different shoot outs: LACR drag strip, Willow Springs Raceway and the Honda test facility in the Mojave desert. Builders could submit their bikes to the magazine editors for consideration. Bikes had to be street legal (lights etc.) and could not overheat, they actually had to drive around for 10-15 mins on the street right before the start of the competition. Several UFO bikes used the F1 assembly and Sims & Rohm took theirs to 208 mph – check out the pic with the girl in the pink bikini!
(Image 1) 2GSXR710
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR710 - 88/92 GSXR750 YOSH FRAME CARB CVRS
Suzuki GSXR 750 Yoshimura carb covers
These carb covers are almost impossible to find, but we have them.
These covers are easily installed onto your chassis with zip ties (recommended) but we've seen velcro used too.
(Image 1) 2GSXRST
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXRST - 88/92 GSXR750/1100 SPRINT TANK
Suzuki GSXR 750 Fuel tank - Sprint
This is a slammed style race fuel tank for you GSXR. You can save quite a few pounds off the top of your bike with this lightweight fuel tank. It comes with one of our flush racing caps on the top and a 3/8" NPT bung in the bottom of the tank for use with a Pingel race valve.
(Image 1) 2YF11
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2YF11 - 92 YOSH F1 UPPER
Yoshimura F1 GSXR750 Upper fairing
This particular fairing was the second version of the F1 fairing used by Yoshimura and several other teams throughout the 92′ Formula USA season. The fairing has a low-slung, raked nose and two large radiator vents on the side of the fairing.
The front radiator shroud was extended back towards the radiator itself to help avoid high pressure bleed off and improve cooling.
All the duct works were filled in to smooth air flow.
Takes a special windscreen and custom bracket
(Image 1) 2YF12
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2YF12 - 92 YOSH F1 LOWER
Yoshimura F1 GSXR750 Lower fairing
This is the lower belly pan that fits the 2YF11 Yoshimura F1 upper fairing. This lower is smooth and does not have the naca duct for the dry clutch – we removed it because it didn’t need it, and it improved the air flow.
(Image 1) 2YF13
(Image 2) 2YF13
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2YF13 - 92 YOSH F1 SUPERBIKE TAIL SECTION
Yoshimura F1 GSXR750 Tail section
We also made a slimmer, sleeker race seat. See below for the undertail.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2YF14 - 92 YOSH F1 DRAFT SHIELD
Yoshimura F1 GSXR750 Under seat enclosure
This anti-drag shield helps control turbulent air around the rear tire – and it looks bitchin’ to boot.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
(Image 1) YF11 - 91 YOSH F1 UPPER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YF11 - 91 YOSH F1 UPPER
Yoshimura F1 GSXR750 Upper fairing
This is one of the most beautifully designed sculpted fairings made for the GSXR. The upper has 4 sharp louvers in the sides to ventilate radiator heat out of the bike. Intake ducts route air through internal ducting back to the air box.
Takes a special windscreen and custom bracket
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YF12 - 91 YOSH F1 LOWER
Yoshimura F1 GSXR750 Lower fairing
Our one piece lower affixes easily and has several vents in it that pull hot air out of the engine compartment.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YF13 - 91 YOSH F1 RACE TAIL
Yoshimura F1 GSXR750 Tail section
Our distinctive Yosh F1 race seat was titled “the big butt seat” by some, at the time. Truth was, it was designed in a fashion that reattaches the air behind the motorcycle, which reduces drag.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YF14 - 91 YOSH F1 DRAFT SHIELD NEED
Yoshimura F1 GSXR750 Under seat enclosure
For underneath the tail section, we make an anti-draft shield that bonds under the subframe and controls the turbulent air swirling around the rear tire.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YGSXR75 - 90 YOSH KYB FRONT FENDER
Yoshimura F1 GSXR750 Front fender
For KYB fork only.
(Image 1) YGSXR76
(Image 2) YGSXR76 - 92 YOSH F1 REAR FENDER,BRACED ARM
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YGSXR76 - 92 YOSH F1 REAR FENDER,BRACED ARM
Yoshimura F1 GSXR750 Rear fender / hugger
Fits “Kit” braced swingarm only.