YF13 - 91 YOSH F1 RACE TAIL
Measurements, fitment, and other pictures...
Yoshimura F1 GSXR750 Tail section
Our distinctive Yosh F1 race seat was titled “the big butt seat” by some, at the time. Truth was, it was designed in a fashion that reattaches the air behind the motorcycle, which reduces drag.
Manufacturing Notes:
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
FAQ's and Reviews
Once again we make every part to order and most often needs custom installation on your part.
Our custom made bodywork is... CUSTOM MADE! So we can make it however you want it.
If you're a previous Airtech customer, our parts are made slightly thicker, 30% heavier with DOUBLE the strength.
If you don't want it thicker, please request "RACE-THIN" in the custom request.
We can also pre-prime or pre-paint your parts for additional charges.
You might also be looking for...
(Image 1) 2GSXR710
2GSXR710 - 88/92 GSXR750 YOSH FRAME CARB CVRS
Suzuki GSXR 750 Yoshimura carb covers
These carb covers are almost impossible to find, but we have them.
These covers are easily installed onto your chassis with zip ties (recommended) but we've seen velcro used too.
(Image 1) 2GSXRST
2GSXRST - 88/92 GSXR750/1100 SPRINT TANK
Suzuki GSXR 750 Fuel tank - Sprint
This is a slammed style race fuel tank for you GSXR. You can save quite a few pounds off the top of your bike with this lightweight fuel tank. It comes with one of our flush racing caps on the top and a 3/8" NPT bung in the bottom of the tank for use with a Pingel race valve.
(Image 1) 2YF11
2YF11 - 92 YOSH F1 UPPER
Yoshimura F1 GSXR750 Upper fairing
This particular fairing was the second version of the F1 fairing used by Yoshimura and several other teams throughout the 92′ Formula USA season. The fairing has a low-slung, raked nose and two large radiator vents on the side of the fairing.
The front radiator shroud was extended back towards the radiator itself to help avoid high pressure bleed off and improve cooling.
All the duct works were filled in to smooth air flow.
Takes a special windscreen and custom bracket
(Image 1) 2YF12
2YF12 - 92 YOSH F1 LOWER
Yoshimura F1 GSXR750 Lower fairing
This is the lower belly pan that fits the 2YF11 Yoshimura F1 upper fairing. This lower is smooth and does not have the naca duct for the dry clutch – we removed it because it didn’t need it, and it improved the air flow.
2YF13 - 92 YOSH F1 SUPERBIKE TAIL SECTION
Yoshimura F1 GSXR750 Tail section
We also made a slimmer, sleeker race seat. See below for the undertail.
2YF14 - 92 YOSH F1 DRAFT SHIELD
Yoshimura F1 GSXR750 Under seat enclosure
This anti-drag shield helps control turbulent air around the rear tire – and it looks bitchin’ to boot.
(Image 1) YF11 - 91 YOSH F1 UPPER
YF11 - 91 YOSH F1 UPPER
Yoshimura F1 GSXR750 Upper fairing
This is one of the most beautifully designed sculpted fairings made for the GSXR. The upper has 4 sharp louvers in the sides to ventilate radiator heat out of the bike. Intake ducts route air through internal ducting back to the air box.
Takes a special windscreen and custom bracket
YF12 - 91 YOSH F1 LOWER
Yoshimura F1 GSXR750 Lower fairing
Our one piece lower affixes easily and has several vents in it that pull hot air out of the engine compartment.
YF14 - 91 YOSH F1 DRAFT SHIELD NEED
Yoshimura F1 GSXR750 Under seat enclosure
For underneath the tail section, we make an anti-draft shield that bonds under the subframe and controls the turbulent air swirling around the rear tire.