SUZUKI GSXR 750 '88-'89
The ’88-’89 Suzuki GSXR 750 Slingshot is unquestionably a fine looking piece of equipment. Airtech has everything you could ever need in the bodywork department for this bike, so there is no excuse for not making your machine look perfect.
We’ve got three different uppers to choose from. First the stock upper with dual headlight holes. We also have an endurance upper with a single hole on the left side. Finally there is the competition upper with no openings at all. This last part can be modified to accept a little trick headlight if you’re running it on the street.
Additionally, we’ve got the front center pieces for both sides of the fairing and a one piece belly pan.
We also have an array of offerings in the seat department, a one piece, stock-appearing, solo race seat, a Yoshimura water-cooled GSXR replica rear end, or the Yoshimura F1 seat. In the fender department, we’ve got both front and rear available.
We also make a rear fender that hangs below the swing arm to ward off heat and oil from the motor and protect the rear tire.
Whip your ride into shape, lighten’er up, and attach some extra bonus goodies. Your bike will never look the same!
(Image 1) 2GSXR710
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR710 - 88/92 GSXR750 YOSH FRAME CARB CVRS
Suzuki GSXR 750 Yoshimura carb covers
These carb covers are almost impossible to find, but we have them.
These covers are easily installed onto your chassis with zip ties (recommended) but we've seen velcro used too.
(Image 1) 2GSXR711
(Image 2) 2GSXR711
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR711 - 88/92 GSXR YOSH DRY CLUTCH DUC
Suzuki GSXR 750 Yoshimura dry clutch duct
Another hard to find Yosh part! This is the small Yoshimura dry clutch naca duct that routes cool air to the dry clutch - or standard clutch for that matter. Cut a small hole in your stock or race fairing and rivet this little piece in. Only available from Airtech!
(Image 1) 2GSXR74
(Image 2) 2GSXR74
(Image 3) 2GSXR74 - 88/92 GSXR750/1100 1 PIECE LOWER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR74 - 88/92 GSXR750/1100 1 PIECE LOWER
Suzuki GSXR 750 Lower fairing
This is the lower belly pan for your GSXR. This is the right and left side and the T-section behind the tire all molded as a one-piece unit. This lightweight fiberglass piece replaces your crash damaged bodywork.
(Image 1) 2GSXR74YR
(Image 2) 2GSXR74YR
(Image 3) 2GSXR74YR - 88/92 YOSH REPLICA 1 PIECE LOWER
(Image 4) 2GSXR74YR - 88/92 YOSH REPLICA 1 PIECE LOWER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR74YR - 88/92 YOSH REPLICA 1 PIECE LOWER
Suzuki GSXR 750 Yoshimura Lower fairing
This is a Yoshimura race belly pan for your GSXR. It is a one piece unit with a closed and extended bottom. Originally designed for the GSXR750 with a 4-1 race system, may require modification to work with your exhaust system especially on a GSXR1100.
Requires trimming around the kickstand for use on a street bike.
(Image 1) 2GSXR75
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR75 - 88/90 GSXR750/1100 SUPERSPORT TAIL
Suzuki GSXR 750 Supersport race tail
This is a cool one-piece race tail for your GSXR. This tail section is already cut out for the stock taillight. Works with the stock GSXR 750 upholstery.
(Image 1) 2GSXR76
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR76 - 88/90 GSXR750 FRONT FENDER
Suzuki GSXR 750 Front fender
Straight replacement for your busted stock fender. Drill the mounting holes, bolt it up and go riding.
(Image 1) 2GSXR77L
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR77L - 88/92 GSXR750/1100 LOWER REAR FNDR
Suzuki GSXR 1100 Lower rear fender
This lower rear fender attaches below the swing arm to help keep the shock and linkage clean.
(Image 1) 2GSXR78
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR78 - 88/90 GSXR750 NUMBER PLATE
Suzuki GSXR 750 Number plate
This is a cool piece for track days or a custom headlight install. It covers up the stock headlight opening.
(Image 1) 2GSXR79
(Image 2) 2GSXR79
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR79 - 88/90 GSXR750 AIR INTAKE GRABBER 2
Suzuki GSXR 750 air grabbers – pair
These sculpted air grabbers do just that, they enlarge the intake area, ‘grab’ air and force it into the ducts. This greatly enhances the flow over the stock ducts.
These covers are easily installed onto your upper fairing with pop rivets
(Image 1) 2GSXRST
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXRST - 88/92 GSXR750/1100 SPRINT TANK
Suzuki GSXR 750 Fuel tank - Sprint
This is a slammed style race fuel tank for you GSXR. You can save quite a few pounds off the top of your bike with this lightweight fuel tank. It comes with one of our flush racing caps on the top and a 3/8" NPT bung in the bottom of the tank for use with a Pingel race valve.
(Image 1) 3GSXR71C
(Image 2) 3GSXR71C - 90 GSXR750 COMPETITION UPPER
(Image 3) 3GSXR71C - 90 GSXR750 COMPETITION UPPER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
3GSXR71C - 90 GSXR750 COMPETITION UPPER
Suzuki GSXR 750 Competition upper fairing
We made this race part for Yoshimura, they asked for a lower windscreen height so this fairing is an inch lower than stock. The thick return in the handlebar opening was because they didn’t run a windscreen bracket on their race bikes and the fairing ears needed to be self supporting. You can install this fairing on your standard fairing bracket, you’ll have to bend the mirror mounts down an inch or so to suit.
(Image 1) 3GSXR71E
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
3GSXR71E - 90 GSXR750 ENDURANCE UPPER
Suzuki GSXR 750 Endurance upper fairing
This is identical in exterior shape to the stock GSXR upper fairing with the exception that one headlight hole has been filled in for endurance race purposes. You get the best of both worlds: one headlight, weight saving, room for a number and that classic endurance style look!
(Image 1) AT26M
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
AT26M - AIRTECH REAR FENDER - MODIFIED
Suzuki GSXR 750 Rear fender
This hugger is a brand new Airtech design for aftermarket overbraced 1st and 2nd gen GSXR750 swingarms like SPF where the brace runs parallel to the arm.
Fit it to modified street & race bikes to keep the rear shock, motor and carbs clean.
Inside width 9"
Outside width 11.75"
Fender length 13"
Depth 6.5"
(Image 1) YGSXR74
(Image 2) YGSXR74 - 90 YOSH GSXR750 SUPERSPORT TAIL
(Image 3) YGSXR74 - 90 YOSH GSXR750 SUPERSPORT TAIL
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YGSXR74 - 90 YOSH GSXR750 SUPERSPORT TAIL
Suzuki GSXR 1100 Yoshimura Supersport race tail
This is a cool one-piece race tail for your GSXR. The taillight is molded in and would have to be cut out for street use. Works with the stock GSXR1100 upholstery, which will pop down with the standard seat locks.
The ‘strap’ in the middle of the seat area is an additional battery hold down strap. Many people cut this part out if they don’t want it.