(Image 1) BRS127
BRS127 - BUELL RS1200 RIGHT FUEL TANK SKIRT
Measurements, fitment, and other pictures...
Buell RS1200 filler panel
Right side filler panel that goes between the tail section and fairing assembly.
Manufacturing Notes:
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
FAQ's and Reviews
Once again we make every part to order and most often needs custom installation on your part.
Our custom made bodywork is... CUSTOM MADE! So we can make it however you want it.
If you're a previous Airtech customer, our parts are made slightly thicker, 30% heavier with DOUBLE the strength.
If you don't want it thicker, please request "RACE-THIN" in the custom request.
We can also pre-prime or pre-paint your parts for additional charges.
You might also be looking for...
(Image 1) BRS1210
BRS1210 - BUELL RS1200 DASH PANEL
Buell RS1200 Dash panel
The picture shows this dash mantle upside down, but this is actually the right part you need for your RS1200. Stock fiberglass pieces are brittle and break easily our lightweight fiberglass piece is a direct replacement. Simply drill the mounting holes, mount it onto your chassis, and go riding.
(Image 1) BRS1211
BRS1211 - 89/93 RS1200 SOLO SEAT COWL
Buell RS1200 Solo seat cowl
This the flip up cowl assembly that works with the long BRS124 tail section. This two-piece design that is molded together is an exact duplicate of the stock Buell tail section. You simply need to drill the mounting holes and install your hardware off of your old tail section on it, mount it onto your bike, and go for a ride.
(Image 1) BRS124
BRS124 - 89/93 RS1200 SUPERSPORT TAIL
Buell RS1200 Tail section
if you're lucky enough to have one of these RS1200's and are unfortunate enough to need a replacement, you are in luck because we still make the parts. This is the long tail section that was used with the flip up solo seat cowl. You're going to have to salvage your old hardware off of your old tail section for it because that stuff is no longer available. Drill the mounting holes, mount everything up, and go riding again.
(Image 1) BRS125
BRS125 - 89/93 RS1200 LISENCE PLATE HOLDER
Buell RS1200 License plate bracket
This is a license plate/ tail light bracket that mounts onto the inside of the long tail. It takes a little trimming and a little bit of epoxy work, but then you can mount it to the inside of your tail section.
(Image 1) BRS126
BRS126 - BUELL RS1200 FUEL TANK
Buell RS1200 Fuel tank
Modern pump gas tears up fuel tanks, especially those old fiberglass tanks like on your Buell. So if you've had gas sitting in your bike for all of these years, chances are that your tank is a goner. We put a factory ethanol resistant epoxy coating in our tanks, and have sold quite a few of these to people who are in the exact situation you're probably in. Need a replacement tank for your Buell? We've got what you need. Give us a call today!
(Image 1) BRS128
BRS128 - BUELL RS1200 LEFT FUEL TANK SKIRT
Buell RS1200 filler panel
Left side filler panel that goes between the tail section and gas tank, and it mounts below the upholstery.
(Image 1) BRS129
BRS129 - BUELL RS1200 FRONT FENDER.
Buell RS1200 Front fender
This is an exact replica of the RS and RSS Buells. Simply drill the mounting holes, mount onto your bike and go for a ride! As you can see we sell this fender in fiberglass but it is also available in carbon fiber call your sales rep for a price in carbon today.