BUELL RR1000 RR1200 BATTLETWIN 1985-'88
Erik Buell started his engineering career at Harley Davidson, but left H-D to pursue an opportunity to market Buell Motor Company 750cc two stroke racebikes to privateer teams competing in the AMA Formula 1 series. The race bike stint was short lived, as the AMA discontinued the series in favor of Superbike less than a season later.
Buell then turned to street bikes. He obtained a large quantity of XR1000 motors via his contacts at H-D, and he used these to create the RR1000 Battletwin. Between 1987 and 1988, Buell delivered 50 bikes to customers, placing the Buell Motor Company on the map.
When his supply of XR1000 motors ran out, Buell adopted the new H-D 1200cc Evolution engine, upgrading the bike and making the necessary changes to package the new power plant. Through the 1989 model year, Buell created an estimated 65 RR1200 bikes.
Airtech has fairings for both models, and even some hard to find race stuff!
Don McCaw at the Bonneville salt flats on his land speed RR1200 circa 1991/92. We have the racing lowers and matching lower tail panels as used on this bike and Battle of the Twins racers.
(Image 1) BRR1S
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR1S - RR1200 UPPER FAIRING - STREET
Buell RR1000 RR1200 Upper fairing- street
Replacement upper with headlight opening.
(Image 1) BRR2A
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR2A - RR1000 LOWER - RIGHT NO DUCT
Buell RR1000 Lower fairing – right
This is the replacement right lower fairing for your Buell RR 1000. It is different from the RR 1200 right lower fairing. The RR1000 lower does NOT have a large duct opening in it.
(Image 1) BRR2B
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR2B - RR1200 LOWER - RIGHT W/ DUCT
Buell RR1200 Lower fairing – right
This is the replacement right lower fairing for your Buell RR 1200. It is different from the RR 1000 right lower fairing. The RR1200 lower fairing has a large duct opening in it.
(Image 1) BRR3
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR3 - RR1000/1200 LOWER FAIRING - LEFT
Buell RR1000 RR1200 Lower fairing – left
This is the replacement left lower fairing for your Buell RR 1000 or RR1200. The left side lower fairing for both models is the same. The inside duct BRR3D is sold separately – listed below.
(Image 1) BRR3D
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR3D - RR1200 LEFT LOWER INNER DUCT
Buell RR1000 RR1200 Lower fairing – inside duct
This is the inside duct for BRR3.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR4 - RR1200 TAIL SECTION
Buell RR1000 RR1200 Tail section
This is the replacement tail section for your Buell RR 1000 or RR1200.
(Image 1) BRR4LP
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR4LP - RR1200 LICENSE PLATE BRACKET
Buell RR1000 RR1200 Upholstery pan
This is license plate bracket for your Buell RR 1000 or RR1200.
(Image 1) BRR4P
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR4P - RR1200 UNDERSEAT ENCLOSURE
Buell RR1000 RR1200 Underseat enclosure
This is underseat enclosure for the tail section for your Buell RR 1000 or RR1200. It can be bonded into the tail section and creates a storage compartment in the tail, accessible by lifting up the upholstery pan BRR4UP listed below.
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR4UP - RR1200 UPHOLSTERY PAN
Buell RR1000 RR1200 Upholstery pan
This is upholstery pan for your Buell RR 1000 or RR1200.
(Image 1) BRR5
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR5 - RR1200 LOWER TAIL FAIRING - RIGHT
Buell RR1000 RR1200 Lower tail fairing – right
This is the replacement right lower tail fairing for your Buell RR 1000/1200. This filler panel fits behind the foot controls and connects the lower fairing to the tail section.
(Image 1) BRR6
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR6 - RR1200 LOWER TAIL FAIRING - LEFT
Buell RR1000 RR1200 Lower tail fairing – left
This is the replacement left lower tail fairing for your Buell RR 1000/1200. This filler panel fits behind the foot controls and connects the lower fairing to the tail section.
(Image 1) BRR7A
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR7A - RR1200 2-PC FENDER - FRONT PART
Buell RR1000 RR1200 Front fender – front part
Replacement front fender part. This is the front half of the 2-piece front fender on the RR1000 and RR1200.
(Image 1) BRR7B
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR7B - RR1200 2-PC FENDER - REAR PART
Buell RR1000 RR1200 Front fender – rear part
Replacement front fender part. This is the rear half of the 2-piece front fender on the RR1000 and RR1200.
(Image 1) BRR8
(Image 2) BRR8
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
BRR8 - RR1200 FUEL TANK
Buell RR1000 RR1200 Fuel tank
This is a replacement fuel tank for the Buell RR1000 and RR1200. The stock tank on your RR was made out of fiberglass as well and by now modern fuel has probably tore up the inside causing all kinds of problems. Airtech can help you by making a brand new tank. We can epoxy coat the inside of your new tank to prevent future problems. Please ask your sales rep when placing the order!