YOSHIMURA GSXR 750 WORLD SUPERBIKE '93
During the 93′ season Yoshimura teamed up with Airtech to do some serious development work on the fairing assembly of their Superbike Suzuki GSXR 750.
A competition upper fairing with a shield that runs back below the bottom triple clamp to seal off the space around the radiator to prevent high pressure bleed off. Yosh used a one piece lower that was comprised of the left and right side panels and the radiator shroud. It’s available.
Either Supersport or Superbike race seats were used in conjunction with anti-draft shields in most cases. Now for sale. The team ran the KYB front end with our front fender and finally settled on a premium design for the rear fender. We’ve got’em available.
Airtech also designed an air box assembly and a sprint fuel tank for y’all to put on your bike. So if you’re looking to restore a 1993 water-cooled superbike or are in the process of building a custom street bike, we can make your life much easier.
(Image 1) 1YWCSB1
(Image 2) 1YWCSB1 - 93 YOSH SUPERBIKE COMP UPPER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
1YWCSB1 - 93 YOSH SUPERBIKE COMP UPPER
Suzuki GSXR 750 ’93 Yoshimura WSBK upper fairing
This is the upper part of the 2-piece Yoshimura race fairing. The ducts are still closed in this picture but we can cut them out for you.
Please note: Fork opening needs to be trimmed out.
This upper works with the 2YWCSB2DB lower
(Image 1) 1YWCSB1D
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
1YWCSB1D - 93 YOSH AIR DUCTS - ROUND 2.5"
Suzuki GSXR 750 ’93 Yoshimura air ducts – round outlet 2.5″
These ducts can be installed with fiberglass, epoxy, silicone caulking or pop rivets. Round outlet with 2.5″ OD. Don’t forget to order your matching SBDH250 smoothbore duct hose from us!
These ducts only work with our 1YWCSB1 upper.
(Image 1) 1YWCSB2
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
1YWCSB2 - 93 YOSH SUPERBIKE LOWER
Suzuki GSXR 750 ’93 Yoshimura lower fairing
This is the lower part of the 2-piece Yoshimura race fairing. This lower does not have oil containment. It has the dimples for the lower mounts and there is a bulge for the stock radiator hose on the left side so this lower is very easy to fit.
If you need oil containment for racing look at the 3YWCSB1 and 3YWCSB2 fairing assembly below.
This piece works with our 1YWCSB1 or 2YWCSB2 upper.
(Image 1) 1YWCSB2DB
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
1YWCSB2DB - 93 YOSH STRETCHED DRAGBIKE LOWER
Suzuki GSXR 750 ’93 Yoshimura dragbike lower fairing – extended
This is a lower that was modified for dragracing and has an extended oil containment bellypan to be used in conjunction with a +8 arm. Overall length is about 42″.
This piece works with our 1YWCSB1 or 2YWCSB2 upper.
(Image 1) 1YWCSBAB
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
1YWCSBAB - 93 YOSH RAM AIR BOX
Suzuki GSXR 750 Yoshimura ram air box ’93
Air ducts not available.
Fits Yosh upper 1YWCSB1.
Please note: This is a race air box and may not clear starter/alternator on a street bike.
(Image 1) 5GSXRAB
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
5GSXRAB - 94/95 GSXR750/1100 AIR BOX
Suzuki GSXR 1100 ’95 Yoshimura airbox
Works with:
’95-’98 GSXR 1100 stock upper fairing 6GSXR11C
The larger than stock intake ducts were glassed into the stock upper.
The airbox can also be used with YWCSB1 Yoshimura race upper, which comes with it’s own larger ducts.
We have smooth bore duct hose available separately, click here.
Please note: This is a race air box and may not clear starter/alternator on a street bike. Requires relocation of fuel valve.
(Image 1) YWCSB1
(Image 2) YWCSB1 - 93 YOSH S/B UPPER FAIRING
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB1 - 93 YOSH S/B UPPER FAIRING
Suzuki GSXR 750 ’93 Yoshimura WSBK upper fairing
This early Yosh upper is short like the stock one with a big one piece lower. This upper does not have any molded in air ducts. Yoshimura used this upper in combination with the YWCSBAB airbox and cut openings to match the ducts that come with that airbox.
This upper fairing uses a standard ’93 GSXR750 windscreen.
Please note: Fork opening needs to be trimmed out.
This piece only works with our YWCSB2 lower.
(Image 1) YWCSB1V
(Image 2) YWCSB1V - 93 YOSH/VALVOLINE UPPER W/ DUCTS
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB1V - 93 YOSH/VALVOLINE UPPER W/ DUCTS
Suzuki GSXR 750 ’94-’95 Yoshimura / Valvoline Suzuki upper fairing
This early Yosh upper is short like the stock one with a big one piece lower. It comes with 2 air ducts that you can rivet or epoxy into the inside of the fairing. You will need matching 2.5″ ID smoothbore duct hose. This upper was used by Valvoline Racing in combination with the 5GSXRAB airbox.
This upper fairing uses a standard 94-’95 GSXR750 windscreen.
This piece only works with our YWCSB2 lower.
(Image 1) YWCSB2
(Image 2) YWCSB2 - 93 YOSH SUPER/BIKE LOWER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB2 - 93 YOSH SUPER/BIKE LOWER
Suzuki GSXR 750 ’93 Yoshimura WSBK lower fairing
This is the lower part of the 2-piece Yoshimura race fairing. It is a big one-piece lower that consists of the two side fairings and a belly pan all in one. There’s no dam for oil containment.
This lower fairing works with either the stock 93, 94-95 GSXR750 upper fairing or the Yoshimura YWCSB1 or YWCSB1V upper fairing.
(Image 1) YWCSB3
(Image 2) YWCSB3
(Image 3) YWCSB3 - 93 YOSH SUPER/BIKE TAIL
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB3 - 93 YOSH SUPER/BIKE TAIL
Suzuki GSXR 750 ’93 Yoshimura Superbike tail section
(Image 1) YWCSB4
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB4 - 93 YOSH SUPER/BIKE DRAFT SHIELD
Suzuki GSXR 750 Yoshimura Superbike underseat enclosure
This is the panel that attaches to the bottom of the YWCSB3 tail section. It cleans up the under side of the tail section and helps to control the parasitical drag and turbulent air that is generated from the rear tire.
Fits 2YWCSB3 as well.
(Image 1) YWCSB5
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB5 - 93 YOSH SUPER/BIKE FRONT FENDER
Suzuki GSXR 750 ’93 Yoshimura WSBK front fender
Fits factory racing KYB (Kayaba) forks only.
(Image 1) YWCSB6
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB6 - 93 YOSH SUPER/BIKE REAR S/A FENDER
Suzuki GSXR 750 ’93 Yoshimura WSBK rear fender
Does not fit stock banana arm, factory kit braced swing arm only!
(Image 1) YWCSB7
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSB7 - 93 YOSH UPPER RADIATOR SHROUD
Suzuki GSXR 750 ’93 Yoshimura WSBK Upper radiator shroud
This piece can be installed underneath the nose between the forks and increases radiator performance by preventing air bleed off over the top of the radiator. Can be combined with YWCSB1, 1V and 1YWCSB1.
(Image 1) YWCSBAB
(Image 2) YWCSBAB
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YWCSBAB - 93 YOSH SUPER/BIKE AIR BOX
Suzuki GSXR 600 ’92-’93 Yoshimura airbox
Works with:
’92-’93 GSXR 600 stock upper fairing GSXR61C
These ducts were pop riveted into the stock uppers.
The airbox can also be used with YWCSB1 Yoshimura race upper, which comes with it’s own ducts.
We have 2″ smooth bore duct hose available separately, click here.
Please note: This is a race air box and does not clear starter/alternator on a street bike.
This airbox comes with intake ducts that will work with the stock street upper or our competition upper GSXR61C. You’ll be cutting out some big square holes on the left and right side of the fairing to fit these big air intakes. You can install the intake ducts with 5-minute epoxy, silicone or rivets. Don’t forget to order some smoothbore duct hose as well!
Works with Mikunis, tight on Keihins. On a street bike, you will have to cut the bottom out of this airbox to work with the starter and the alternator (in a street application, the box won’t pressurize, you will just be routing cool air to the carbs).