- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF7 - 94/97 RF900 FUEL TANK
Suzuki RF600 Fuel tank
Our lightweight fuel tank improves the performance of your bike. You see, if you weigh your stock tank you’ ll find that it weights about 13 pounds, our lightweight fiberglass tank only weighs about 4 pounds! This is a substantial weight reduction off of the top of your motorcycle. You will defiantly notice-handling improvements, as the bike will flick easier from right to left around corners. This tank comes with one of our cool racing gas caps and also comes with a 3/8 NPT fuel bung in the bottom of the tank for use with a single racing fuel valve. Increase the handling performance of your bike with our lightweight fuel tank today!
(Image 1) RF6
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF6 - 94/97 RF900 SUPERSPORT TAIL SECTIO
Super sport race tail
This cool race tail section is the right and left seat sides, the solo seat cowl, and the tail light area all molded as a one piece unit. This one-piece design hides the passenger part of your long upholstery to make it look like a one-piece race tail. Simply slide your upholstery into this fiberglass tail section assembly and then take that assembly and install it onto your chassis. To remove this off of your bike simply pop the seat locks and remove the whole rear clip off of the chassis in one easy step. This can easily be used on a street bike if you cut the taillight hole open.
(Image 1) RF4
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF4 - 94/97 RF900/600 FRONT FENDER
Suzuki RF600 Front fender
This is a direct replacement fender for the RF600.
(Image 1) RF3
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF3 - 94/97 RF900/600 LEFT LOWER
Suzuki RF600 Left lower fairing
This is our one-piece left hand fairing assembly for your GF600. This is the lower assembly and the vented access doors all molded as a clean one-piece unit.
(Image 1) RF2
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF2 - 94/97 RF900/600 RIGHT LOWER
Suzuki RF600 Right lower fairing
This fairing assembly is all of the right panels molded as a one-piece unit. The right fairing lower and the vented access door has been molded together for a clean one-piece design. Replace your expensive and rare body panels with our lightweight fiberglass pieces.
(Image 1) RF1C
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
RF1C - 94/97 RF900/600 COMPETITION UPPER
Suzuki RF600 Competition upper fairing
What we have here is a race upper fairing for your RF600. Basically we’ ve taken the stock upper fairing, drilled in the headlight holes and the turn signal holes for race purposes. This is a great piece for track day guys who would like to save their expensive upper and headlight assembly from any damage. A custom street bike guy might like this because they can cut their own headlight shape into the front of the fairing. Replace your crash damaged bodywork with our lightweight inexpensive fiberglass body panel today!