(Image 1) 3GSXR71C
(Image 2) 3GSXR71C - 90 GSXR750 COMPETITION UPPER
(Image 3) 3GSXR71C - 90 GSXR750 COMPETITION UPPER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
3GSXR71C - 90 GSXR750 COMPETITION UPPER
Suzuki GSXR 750 Competition upper fairing
We made this race part for Yoshimura, they asked for a lower windscreen height so this fairing is an inch lower than stock. The thick return in the handlebar opening was because they didn’t run a windscreen bracket on their race bikes and the fairing ears needed to be self supporting. You can install this fairing on your standard fairing bracket, you’ll have to bend the mirror mounts down an inch or so to suit.
(Image 1) 2GSXR711
(Image 2) 2GSXR711
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR711 - 88/92 GSXR YOSH DRY CLUTCH DUC
Suzuki GSXR 750 Yoshimura dry clutch duct
Another hard to find Yosh part! This is the small Yoshimura dry clutch naca duct that routes cool air to the dry clutch - or standard clutch for that matter. Cut a small hole in your stock or race fairing and rivet this little piece in. Only available from Airtech!
(Image 1) 2GSXR710
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR710 - 88/92 GSXR750 YOSH FRAME CARB CVRS
Suzuki GSXR 750 Yoshimura carb covers
These carb covers are almost impossible to find, but we have them.
These covers are easily installed onto your chassis with zip ties (recommended) but we've seen velcro used too.
(Image 1) 2GSXR71
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
2GSXR71 - 88/89 GSXR750 STREET UPPER
Suzuki GSXR 750 Street upper fairing
This is a direct replacement fairing, just the turn signal holes have been filled in. Simply drill the mounting holes and mount onto your chassis. Replace your crash damaged bodywork with our lightweight fiberglass piece!
(Image 1) AT26M
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
AT26M - AIRTECH REAR FENDER - MODIFIED
Suzuki GSXR 750 Rear fender
This hugger is a brand new Airtech design for aftermarket overbraced 1st and 2nd gen GSXR750 swingarms like SPF where the brace runs parallel to the arm.
Fit it to modified street & race bikes to keep the rear shock, motor and carbs clean.
Inside width 9"
Outside width 11.75"
Fender length 13"
Depth 6.5"