SUZUKI GSXR 750 '85 CANADIAN / EURO / ASIAN / AUSTRALIAN
Pictured with its American counterparts is our ravishing Canadian vix– er, version of the Suzuki GSXR 750 bodywork.
The Canadian/european 1st generation GSXR750 differs from the American version in several ways. To begin with, there is a small air intake duct on each center panel in front of the radiator. Three cool looking exhaust vents are cut into the back of both center side pieces. The upper fairing is slightly wider than the American version and attaches to the center panels with three bolts rather than two. The return under the headlight is also extended and uses only one bolt to mount rather than two like the
US unit.
So, Airtech has a stock upper, right and left center sides and a two piece lower. Save some weight over the stock pieces and make your bike look mega-trick. Call us.
Need a seat? Not only do we offer the a one-piece tail section that replaces the stock three-piece, we also offer it with a solo seat cowl molded into it for that race look. How about an ’86 GSXR Limited edition race seat? No problem, we’ve got what you need!
We’ve figured out a parts combo you can use to build an XR41 replica out of a 1st gen GSXR750. You will have to make or modify your own fairing brackets.
The original XR41 shown above…
and this is the replica.
You use a Hammer half fairing and cut the lower flange off. The Hammer upper will now mate up with a set of ’85 (euro/Canadian) GSXR lower fairings. A little more trimming at the back edge to even them up.
The bottom fairings may interfere with the exhaust headers so you may have to trim around it or do a bit of glass work in that area.
(Image 1) YT1
(Image 2) YT1 - 86/87 TORNADO UPPER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YT1 - 86/87 TORNADO UPPER
Suzuki GSXR 750 Yoshimura Tornado Upper
This is the Yoshimura Tornado style bodywork for the GSXR 750. Works only with the YT2 lower belly.
Takes a special windscreen & headlight cover and requires bracket fabrication. It does not use the stock GSXR headlight (we’ve been told CiBie makes a light that fits).
(Image 1) YT2
(Image 2) YT2 - 86/87 TORNADO LOWER
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YT2 - 86/87 TORNADO LOWER
Suzuki GSXR 750 Yoshimura Tornado Lower
This is the lower belly pan that fits the YT1 Yoshimura Tornado upper fairing.
(Image 1) YT3
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YT3 - 86/87 TORNADO SUPERBIKE TAIL
Suzuki GSXR 750 Yoshimura Tornado Tail section
This is a real cool designed tail section for the first generation of GSXR chassis. This will not work with a stock GSXR gas tank, because the front of the seat assembly is rounded to work with the Tornado tank as the stock GSXR tank is straight across the back.
If you were to put this on a chassis with a stock GSXR tank you would have a half moon shaped gap in the front of the seat
(Image 1) YT3P
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YT3P - 86/87 TORNADO SEAT PAN
Suzuki GSXR 750 Yoshimura Tornado Tail Upholstery pan
This is the fiberglass pan that fits onto the YT3 Tornado seat assembly. Use this pan to upholster for a finished look on your cool Tornado tail section.
(Image 1) YT4
(Image 2) YT4 - 86/87 TORNADO FUEL TANK
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YT4 - 86/87 TORNADO FUEL TANK
Suzuki GSXR 750 Yoshimura Tornado Race Fuel Tank
The shape of this tank is definitely cool! The top of the tank is slightly lower and the bottom a bit wider than the stock GSXR tank. It also comes with our race aluminum gas cap and a 3/8″ NPT bung in the bottom of the tank for a Pingle r
(Image 1) YXR511
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YXR511 - YOSHIMURA XR51 UPPER FAIRING
Yoshimura XR51 Upper fairing
This is the Yoshimura XR51 race upper. Works only with the XR5112 lower belly. This upper fairing can also be used by itself for endurance racing.
(Image 1) YXR512
- We fabricate each fiberglass part to order.
- Fabrication Lead Time UPDATE: Most fiberglass orders will ship within 6 weeks.
- *This part requires CUSTOM installation.
- Cutting, Sanding, Drilling, AND PAINTING likely required.
- Of course, all products require installation once you receive. Common sense is also required.
YXR512 - YOSHIMURA XR51 LOWER FAIRING
Yoshimura XR51 Lower fairing
This is the lower belly pan that fits the YXR511 Yoshimura XR51 upper fairing.